Molybdenum Ore Dressing Process

Molybdenum is an important rare metal resource. And molybdenite (MoS2) is the most widespread among various molybdenum ores, almost 99% molybdenum production is obtained from molybdenite in the world.
Single molybdenum and copper-molybdenum ore are the two most common molybdenum minerals in the mineral processing plant. The main useful mineral in single molybdenum ore is molybdenite. Because of the good natural buoyancy of molybdenum ore, Xinhai often adopts direct floatation process after crushing and grinding. And the main useful minerals in the copper-molybdenum ore are chalcopyrite, pyrocopper, molybdenum and so on. In the practice of production, Xinhai usually adopts bulk flotation process that floats copper-molybdenum bulk concentrate firstly then separates copper-molybdenum.
What’s more, single molybdenum ore and copper-molybdenum ore have low hardness, they are easy to become sliming in the grinding process, so Xinhai often uses stage grinding+stage the flotation process. The primary molybdenum ore has a very low grade (only 0.01~0.4%, above 0.2% is rich ore), which should be several times of cleaning in the flotation process (4~10 times).
Molybdenum ore dressing equipment mainly includes crusher, screen, ball mill, classifier, flotation cell, thickener, filter, etc.
Introduction:
1. Crushing and Grinding
Single molybdenum ore has low grade, fine particle size and complex composition. The typical crushing and screening process is coarse crushing, self-grinding, screening and fine grinding. The raw single molybdenum ore is crushed to the appropriate grinding feed size. The main crushing and screening equipment is shown below:
EquipmentTypeParticle Size(mm)
Jaw Crusher (coarse crushing, secondary crushing)Swinging Jaw Crusher160~320
Cone Crusher(secondary crushing, fine crushing)Spring Cone Crusher, Hydraulic Cone Crusher22~75
ScreenRound Vibrating Screen(YA), Linear Vibrating Screen0~12
Autogenous Millwet autogenous mill0~80

Jaw Crusher

Spring Cone Crusher

Round Vibrating Screen(YA)
2. Grinding
Because single molybdenum ore and copper-molybdenum ore have low hardness, they are easy to become sliming in the grinding process, so Xinhai often uses stage grinding+stage the flotation process. The typical grinding process is one stage grinding, classifying, roughing, two-stage grinding, stage, classifying, one cleaning, three-stage grinding, classification, two cleaning, four stage grinding, classifying, 3~5 times cleaning, thickening and dewatering. The main grinding equipment is shown below:
EquipmentType
GrindingGrid Type Ball Mill, Overflow Type Ball Mill, Rod Mill
ClassifyingSpiral Classifier, Hydrocyclone
FlotationMechanical Agitation Type Flotation Cell, Air-inflation Mechanical Agitation Floatation Cell
ThickeningPeripheral Transmission Thickener, Hydraulic Motor Driving Center Thickener, Efficient Deep Cone Thickener, Tilted Plate Thickener
FilteringVacuum Filter, Ceramic Filter, Drum Filter

Grid Type Ball Mill

Overflow Type Ball Mill

High Weir Spiral Classifier
3. Separation
Copper and molybdenum grade in copper-molybdenum ore is not high. If adopting differential flotation process, the processing capacity of slurry is larger and the production cost is much higher. Therefore, copper-molybdenum ore beneficiation process basically adopts coarse grinding, classifying, and bulk flotation process to get copper-molybdenum bulk concentrate, fine grinding, classifying, reagent removal, copper-molybdenum separation, thickening and filtering process. The involved copper-molybdenum separation has always been the technical difficulty for copper-molybdenum ore beneficiation process. At present, the developed copper-molybdenum separation technologies include conventional flotation process, nitrogen flotation process, pulsating high magnetic separation process and passivation process.
Conventional floatation process: Xinhai usually adopts molybdenum float by copper depression process. The key part of this process is to realize the copper inhibition. Currently, the effective inhibitors include inorganic substances (such as sodium sulfide, cyanide, etc.), organism (ethanethiol) and sodium silicate.
Nitrogen flotation process: Adding a certain amount of nitrogen to the slurry, which make those inhibitors (such as sodium sulfide, sodium bisulfide, etc.) with less pollution replace the poisonous inhibitors (cyanide).
Pulsating high magnetic separation process: Since chalcopyrite is weak magnetic mineral, molybdenite is on-magnetic mineral. Therefore, they can be separated by pulsating high magnetic separation process.
Passivation process: In bulk concentrate, the copper ore surface is oxidized by adjusting slurry temperature and PH value, so that copper-molybdenum separation can be achieved by hydrophily or hydrophobicity of copper minerals.

评论

此博客中的热门博文

Common Problems and Solutions of Jigging Process

Seven Common Froth Flotation Processes and Their Applicable Conditions

What are the Graphite Mining Processes?